Wednesday, October 29th 2025, 12:22am UTC+1

Giriş yapmadınız.

  • Giriş
  • Kayıt

Unbricking ICY BOX IB-4220-B

Sayın ziyaretçi, NAS Forum sitesine hoş geldiniz. Eğer buraya ilk ziyaretiniz ise lütfen Yardım bölümünü okuyunuz. Yardım bölümü bu sitenin nasıl çalıştığını açıklamaktadır. Site özelliklerinin tümünü kullanabilmeniz için öncelikle kayıt yaptırmanız gerekmektedir. Kayıt yaptırmak için kayıt formunu okuyabilir ya da kayıt işlemi hakkında daha fazla bilgi edinebilirsiniz. Eğer önceden kayıt yaptırdıysanız, buraya tıklayarak giriş yapabilirsiniz.

bbanica

Acemi

Mesajlar: 8

1

Saturday, December 18th 2021, 7:18pm

Unbricking ICY BOX IB-4220-B

Hello,

I have the following NAS ICY BOX IB-NAS4220-B image and when I tried to update the firmware, it breaks(brick).


I tried to reach it through j2 port by attached scheme (2 RXD,3 TXD,5 GND,10 VCC 3.3V) image and with the help of ft232rl image , but there was no success. I was reading your MRT unbricking guide. Would you tell me how it should happen the connection and the recovery, please? Also, I will be happy if you tell me where I’m wrong.
Thank you.
bbanica belirtilen dosyaları ekledi:
  • scheme.jpg (50.02 kB - 19 defa indirildi - Son indirme: Oct 3rd 2025, 11:53am)
  • IB-NAS4220-B.jpg (60.92 kB - 18 defa indirildi - Son indirme: Oct 3rd 2025, 12:34pm)
  • FT2332RL.jpg (46.65 kB - 23 defa indirildi - Son indirme: Oct 9th 2025, 12:57pm)

bbanica

Acemi

Mesajlar: 8

2

Saturday, December 25th 2021, 9:43pm

Will it be possible to recover?

HWguru

NAS2000-Team

Mesajlar: 1,039

Konum: Wien

3

Sunday, December 26th 2021, 8:56pm

Yes, it will be possible for sure.

1. try to reach the bootloder with the serial 3.3V adapter connected to the serial port
connect GND, 3.3V, Rx of NAS with Tx of adapter and vice versa.
If this works you can reflash the firmware. If not we go to step 2

2.Connect the JTAG signals with the FTDI adapter - Link (Set the Jumper to 3.3V, connect GND, 3.3V, TCK, TMS, TDI, TDO)
With NAS_Flashtool you can reflash the bootloader an then you go to step 1

I willl try to find some JTAG guide. Many links are dead unfortunately.
Maybe this thread helps you although it is for a different board but the procedure is the same.

Merry Christmas,
HWguru
Leute ohne Laster haben oft wenige Tugenden...
NAS2000 2.3.2.IB.2.RS.1+Lüfterabschaltung+SSH+do_it+zusätzliche commandline tools+changed root password
1. suchen - lesen - Google - lesen - 1. Fragen gehören ins Forum, dann profitieren alle davon!

bbanica

Acemi

Mesajlar: 8

4

Monday, January 10th 2022, 10:08pm

Everything is ok, but the download link of the program NAS_Flashtool is not working. Is there another place where I can download it?

HWguru

NAS2000-Team

Mesajlar: 1,039

Konum: Wien

5

Monday, January 10th 2022, 11:28pm

Hi,
I had to fix a file. Hopefully it should work now. Please give it a try.

HWguru
Leute ohne Laster haben oft wenige Tugenden...
NAS2000 2.3.2.IB.2.RS.1+Lüfterabschaltung+SSH+do_it+zusätzliche commandline tools+changed root password
1. suchen - lesen - Google - lesen - 1. Fragen gehören ins Forum, dann profitieren alle davon!

bbanica

Acemi

Mesajlar: 8

6

Monday, January 10th 2022, 11:34pm

Yes, the file can be downloaded, I’m going to try the repair of the NAS. Thank you very much. :worthy:

bbanica

Acemi

Mesajlar: 8

7

Tuesday, January 11th 2022, 2:02am

So, let’s if I understand you right. I use J1 of the NAS and of the plate FT232RI Cable Type 4 and then I connect them like the following:


Kaynak kod

 
1
2
3
4
5
6
7

Adapter(FT232RL) - NAS JTAG signal(J1)
RTS - 5 TDI
TxD - 7 TMS
RxD - 9 TCK
CTS - 13 TDO
GND - 10 GND
2VCC - 17 DBGRQ



Then I connect Adapter to the computer and start NAS_Flashtool and go with JTAG Test?

HWguru

NAS2000-Team

Mesajlar: 1,039

Konum: Wien

8

Tuesday, January 11th 2022, 9:45am

Hi,
be sure that your adapter is jumpered for 3.3V operation.
DBGRQ must be connected with VCC (J1 Pin 1 or 2) of the mainboard and not to the adapter.
Maybe VCC connection of the adapter to the mainboard is not needed. It should be powered by USB. This depends on the adapter.

For the first test you don't need the NAS.
Only connect TDI with TDO of the adapter and run the Test.
You should get a message like "Short plug detected". This ensures that the software and adapter works as intended.

Then connect the adapter with the nas and run the test again.
If it is ok you may flash the bootloader.

Good luck,
HWguru
Leute ohne Laster haben oft wenige Tugenden...
NAS2000 2.3.2.IB.2.RS.1+Lüfterabschaltung+SSH+do_it+zusätzliche commandline tools+changed root password
1. suchen - lesen - Google - lesen - 1. Fragen gehören ins Forum, dann profitieren alle davon!

bbanica

Acemi

Mesajlar: 8

9

Wednesday, January 12th 2022, 5:50pm

After the test, the answer is:

Kaynak kod

 
1

Cable type 4 detected.Short plug detected.


The adapter on 3,3 V. Тhen connect the adapter to NAS.

Kaynak kod

 
1
2
3
4
5
6
7
8
9

Adapter(FT232RL) - NAS JTAG signal(J1)
RTS - 5 TDI
TxD - 7 TMS
RxD - 9 TCK
CTS - 13 TDO
GND - 10 GND

NAS JTAG signal(J1)
1,2VCC - 17 DBGRQ

After that I start the test again ant answer is:

Kaynak kod

 
1
2

Error: - No cable detected - Testdevice not connected
Some errors detected!



I tried with another adapter(ft232), but the program stopped working(not responding).

Bu mesaj 1 defa düzenlendi; son düzenleyen "bbanica" (Jan 12th 2022, 5:58pm)

HWguru

NAS2000-Team

Mesajlar: 1,039

Konum: Wien

10

Thursday, January 13th 2022, 8:22pm

Hi,
then try to connect VCC of J1 with VCC of the adapter.
Did you power the mainboard? After having connected all signals you have to turn on the mainboard before running the test.
The error means that there is no communication with the NAS.
Leute ohne Laster haben oft wenige Tugenden...
NAS2000 2.3.2.IB.2.RS.1+Lüfterabschaltung+SSH+do_it+zusätzliche commandline tools+changed root password
1. suchen - lesen - Google - lesen - 1. Fragen gehören ins Forum, dann profitieren alle davon!

bbanica

Acemi

Mesajlar: 8

11

Saturday, January 15th 2022, 1:38am

I’m sorry for late answer but my adapter wasn’t working properly and I had to order a new one.
I have an access already with the program, after the adapter was connected to nasa with JTAG test I received the following message:



Kaynak kod

 
1
2
3
4
5
6
7
8

Cable type 4 detected.
Device is in debug-mode - OK

CPU-Type SL3516 detected.

Flash-Manufacturer: 0x01
Flash-Device-ID: 227e-2221-2201
Flash type - OK


I rewrote boot to nasa with this one from the forum.

RedBoot_4220

I want to ask what is next and how to connect the bootloder?

HWguru

NAS2000-Team

Mesajlar: 1,039

Konum: Wien

12

Sunday, January 16th 2022, 11:51am

Now you connect the 3.3V adapter to the serial console. You should see the messages from the bootloader.
Then you can flash the parts (kernel, ramdisk, app) of the firmware. The files are loaded through network.

The MRT unbricking guide (IB-4220 behaves like the MRT GIGANAS) and/or this thread about Openwrt on NAS-4220 may help.
Leute ohne Laster haben oft wenige Tugenden...
NAS2000 2.3.2.IB.2.RS.1+Lüfterabschaltung+SSH+do_it+zusätzliche commandline tools+changed root password
1. suchen - lesen - Google - lesen - 1. Fragen gehören ins Forum, dann profitieren alle davon!

bbanica

Acemi

Mesajlar: 8

13

Thursday, January 20th 2022, 9:56pm

Hi,

I connected the device by the instructions, connect through terminal (putty) and I chose option “Y” and "2" (TFTP). After that I wrote the IP and the name of the file, and appears this error:

TFTP Error

I feel like I can’t make the settings of the TFTP server?

HWguru

NAS2000-Team

Mesajlar: 1,039

Konum: Wien

14

Friday, January 21st 2022, 12:33am

Hi,
you are very near to the final!

The TFTP server and the NAS have to be in the same subnet.

Maybe you have to configure your server manually to something like 192.168.2.xx
Leute ohne Laster haben oft wenige Tugenden...
NAS2000 2.3.2.IB.2.RS.1+Lüfterabschaltung+SSH+do_it+zusätzliche commandline tools+changed root password
1. suchen - lesen - Google - lesen - 1. Fragen gehören ins Forum, dann profitieren alle davon!

Benzer konular